# the presence of the "-R" option, so there is a strong case for enabling it. However, some broken FTP clients such as "ncftp" and "mirror" assume # default to avoid remote users being able to cause excessive I/O on large # You may activate the "-R" option to the builtin ls. # the user does not have write access to the top level directory within the # (Warning! chroot'ing can be very dangerous. If chroot_local_user is YES, then this list becomes a list of # You may specify an explicit list of local users to chroot() to their home # the possible risks in this before using chroot_local_user or # You may restrict local users to their home directories. #banned_email_file=/etc/vsftpd.banned_emails # useful for combatting certain DoS attacks. # You may specify a file of disallowed anonymous e-mail addresses. #ftpd_banner=Welcome to blah FTP service. # You may fully customise the login banner string: # ASCII mangling is a horrible feature of the protocol. # predicted this attack and has always been safe, reporting the size of the # attack (DoS) via the command "SIZE /big/file" in ASCII mode. # Beware that on some FTP servers, ASCII support allows a denial of service Turn on the below options to have the server actually do ASCII # By default the server will pretend to allow ASCII mode but in fact ignore # however, may confuse older FTP clients. # recommended for security (the code is non-trivial). # Enable this and the server will recognise asynchronous ABOR requests. # ftp server can use as a totally isolated and unprivileged user. # It is recommended that you define on your system a unique user which the # You may change the default value for timing out a data connection. # You may change the default value for timing out an idle session. # Note that the default log file location is /var/log/xferlog in this case. # If you want, you can have your log file in standard ftpd xferlog format. # You may override where the log file goes if you like. Note! Using "root" for uploaded files is not # If you want, you can arrange for uploaded anonymous files to be owned by # Make sure PORT transfer connections originate from port 20 (ftp-data). # times returned by the MDTM FTP command are also affected by this # If enabled, vsftpd will display directory listings with the time # Activate directory messages - messages given to remote users when they # Uncomment this if you want the anonymous FTP user to be able to create # obviously need to create a directory writable by the FTP user. # has an effect if the above global write enable is activated. # Uncomment this to allow the anonymous FTP user to upload files. # if your users expect that (022 is used by most other ftpd's) # Uncomment this to enable any form of FTP write command. # Uncomment this to allow local users to log in. # Allow anonymous FTP? (Disabled by default). # addresses) then you must run two copies of vsftpd with two configuration If you want that (perhaps because you want to listen on specific It is not necessary to listen on *both* IPv4 and IPv6 # on the IPv6 "any" address (::) will accept connections from both IPv6 # This directive enables listening on IPv6 sockets. # Run standalone? vsftpd can run either from an inetd or as a standalone # Please read the nf.5 manual page to get a full idea of vsftpd's # READ THIS: This example file is NOT an exhaustive list of vsftpd options. # Please see nf.5 for all compiled in defaults. # loosens things up a bit, to make the ftp daemon more usable. # The default compiled in settings are fairly paranoid. All I want to do is to set up a plain FTP server that the printer can connect to. If I use port 22 I get an "Access denied". If I use port 21 or any other I get an "ECONNREFUSED" error. So I downloaded FileZilla to test the FTP. Whenever I try to scan-to-ftp I get an connection error without further details. The only two things I am not sure about are passive mode and port. The Brother itself has following options: IP, user, password, destination folder, passive mode and port. "jens" is a real local user with permission to modify /Family/Scans. Third, created a file named /etc/vsftpd.chroot_list and added "jens" (the user the printer uses to connect to the FTP server). The Brother is supposed to save the scans in a directory named /Family/Scans. The aim is to set up an FTP server (only for the local network) so I can use the scan-to-ftp feature again. I changed the Qnap NAS to a Debian server. I am used to using a Qnap NAS as a FTP server for this task which worked fine. The only network feature it has is scan-to-ftp.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |